Reduced VOC Paint Data Sheets101.14LL
Cashmere°
Interior Acrylic Low Lustre
D17-150 Series
CHARACTERISTICS
Cashmere Interior Latex glides on buttery
smooth and levels out... giving walls an
elegant, silky rich look. The result is a
difference you can definitely see and feel.
• Ultra -smooth, rich, silky finish.
• Silky, low -stipple appearance that looks good
from all angles.
• Looks, feels and applies smooth and buttery.
• Outstanding coverage and hide.
• Paint and Primer in one.
• Scrubbable for easy cleaning and
maintenance.
• Ideal for residential spaces.
Color: Most Colors
To optimize hide and color development, always use
the recommended P-Shade primer
Coverage: 350 - 400 sq ft per gallon
@ 4 mils wet; 1.6 mils dry
Drying Time, @ 77°F, 50% RH:
Touch:
1 Hour
Recoat:
4 Hours
Drying and recoattimes are temperature, humidity, and
film thickness dependent
Finish:
5-15 units @ 60°
35-45 @ 85°
Tinting with CCE only:
Base:
oz. per
Strength:
gallon
Hi Reflective White
0-6
SherColor
Extra White
0-7
SherColor
Deep Base
4-12
SherColor
Ultradeep Base
10-12
SherColor
Extra White D17WO0151
(may vary by color)
V.O.C. (less exempt solvents):
less than 50 grams per litre; 0.42 lbs. per gallon
As per 40 CFR 59 406
Volume Solids:
41 ± 2%
Weight Solids:
53 ± 2%
Weight per Gallon:
10.85 Ibs
Flash Point:
N.A.
Vehicle Type:
Acrylic
Shelf Life:
36 months unopened
COMPLIANCE
As of 0811012021, Complies with
OTC
Yes
OTC Phase II
Yes
S.C.A.Q.M.D.
Yes
CARB
Yes
CARB SCM 2007
Yes
CARB SCM 2020
Yes
Canada
Yes
LEED® v4 & v4.1 Emissions
No
LEED® v4 & v4.1 V.O.C.
Yes
EPD-NSF® Certified
No
MIR-Manufacturer Inventory
No
MPI®
No
APPLICATION
Apply at temperatures above 50°F.
No reduction needed.
Brush:
Use a nylon -polyester brush.
Roller:
Use 3/8-3/4 inch nap synthetic cover.
For specific brushes and rollers, please refer
to our Brush and Roller Guide on sherwin-
williams.com
Spray —Airless
Pressure 2000 p.s.i.
Tip .017-.021 inch
APPLICATION TIPS
Make sure product is completely agitated
(mechanically or manually) before use.
Priming and application of two coats at the
recommended film thickness can help where
hiding of a previous coating or application to
new drywall is a factor.
LpYIR
rn+
EARTH
SHERWIN
WILLIAMS.
SPECIFICATIONS
Drywall:
Self -prime using 2 coats of Cashmere Interior
or
1 coat Premium Wall and Wood Primer
2 coats Cashmere Interior
Masonry - Block: (can be filled to provide a
smooth surface or primed if it i; a high pH substrate)
1 coat Loxon Acrylic Block Surfacer
or
1 coat Loxon Concrete & Masonry Primer
2 coats Cashmere Interior
Plaster:
1 coat Loxon Concrete & Masonry Primer
2 coats Cashmere Interior
Previously Painted:
1-2 coats Cashmere Interior
Wood:
1 coat Premium Wall and Wood Primer
2 coats Cashmere Interior
If the wood has bleeding (such as tannin or knot -holes), prime
with Multi -Purpose Primer.
Other primers may be appropriate.
When repainting involves a drastic color
change, a coat of primer will improve the
hiding performance of the topcoat color.
08/2021 www.sherwin-williams.com continued on back
Cashmere®
Interior Acrylic Low Lustre
SURFACE PREPARATION
WARNING! Removal of old paint by sanding,
scraping or other means may generate dust or
fumes that contain lead. Exposure to lead dust
or fumes may cause brain damage or other
adverse health effects, especially in children or
pregnant women. Controlling exposure to lead
or other hazardous substances requires the
use of proper protective equipment, such as
a properly fitted respirator (NIOSH approved)
and proper containment and cleanup. For more
information, call the National Lead Information
Center at 1-800-424-LEAD (in US) or contact
your local health authority.
Remove all surface contamination by washing
with an appropriate cleaner, rinse thoroughly
and allow to dry. Existing peeled or checked
paint should be scraped and sanded to a
sound surface. Glossy surfaces should be
sanded dull. Stains from water, smoke, ink,
pencil, grease, etc. should be sealed with the
appropriate primer -sealer. Recognize that any
surface preparation short of total removal of the
old coating may compromise the service length
of the system.
Caulking:
Gaps between walls, ceilings, crown moldings,
and other interior trim can be filled with the
appropriate caulk after priming the surface.
Drywall:
Fill cracks and holes with patching paste/
spackle and sand smooth. Joint compounds
must be cured and sanded smooth. Remove
all sanding dust.
Masonry, Concrete, Cement, Block:
All new surfaces must be cured according
to the supplier's recommendations —usually
about 30 days. Remove all form release and
curing agents. Rough surfaces can be filled to
provide a smooth surface. If painting cannot
wait 30 days, allow the surface to cure 7 days
and prime the surface with Loxon Concrete
and Masonry Primer.
SURFACE PREPARATION
Mildew:
Prior to attempting to remove mildew, it is
always recommended to test any cleaner on a
small, inconspicuous area prior to use. Bleach
and bleaching type cleaners may damage or
discolor existing paint films. Bleach alternative
cleaning solutions may be advised.
Mildew may be removed before painting by
washing with a solution of 1 part liquid bleach
and 3 parts water. Apply the solution and scrub
the mildewed area. Allow the solution to remain
on the surface for 10 minutes. Rinse thoroughly
with water and allow the surface to dry before
painting. Wear protective eyewear, waterproof
gloves, and protective clothing. Quickly wash
off any of the mixture that comes in contact with
your skin. Do not add detergents or ammonia
to the bleach -water solution.
Plaster:
Bare plaster must be cured and hard. Textured,
soft, porous, or powdery plaster should be
treated with a solution of 1 pint household
vinegar to 1 gallon of water. Repeat until the
surface is hard, rinse with clear water and allow
to dry.
Wood:
Sand any exposed wood to a fresh surface.
Patch all holes and imperfections with a wood
filler or putty and sand smooth.
CAUTIONS
For interior use only.
Protect from freezing.
Non-photochemically reactive.
Before using, carefully read CAUTIONS
on label
CRYSTALLINE SILICA: Use only with adequate
ventilation To avoid overexposure, open windows and
doors or use other means to ensure fresh air entry during
application and drying. If you experience eye watenng,
headaches, or dizziness, increase fresh air, or wear
respiratory protection (NIOSH approved) or leave the
area. Adequate ventilation required when sanding or
abrading the dried film. if adequate ventilation cannot be
provided wear an approved particulate respirator(NIOSH
approved). Follow respirator manufacturer's directions
for respirator use. Avoid contact with eyes and skin.
Msh hands after using. Keep container closed when
not in use. Do not transfer contents to other containers
for storage. FIRST AID: In case of eye contact, flush
thoroughly with large amounts of water. Get medical
attention if irritation persists. If swallowed, call Poison
Control Center, hospital emergency room, Or phys'ctan
immediately. DELAYED EFFECTS FROM LONG TERM
OVEREXPOSURE. Abrading or sanding of the dry film
may release crystalline silica which has been shown
to cause lung damage and cancer under long term
exposure. WARNING: This product contains chemicals
known to the State of California to cause cancer and
birth defects or other reproductive harm. DO NOT
TAKE INTERNALLY. KEEP OUT OF THE REACH OF
CHILDREN.
HOTW 08/10/2021 D17WO0150 1432
CLEANUP INFORMATION
Clean spills, spatters, hands and tools
immediately after use with soap and
warm water After cleaning, flush spray
equipment with compliant cleanup solvent
to prevent rusting of the equipment. Follow
manufacturer's safety recommendations
when using solvents.
The information and recommendations set forth in this Product Data Sheet are based upon tests conducted by or on behalf of The Sherwin-Williams Company. Such information
and recommendations set forth herein are subject to change and pertain to the product offered at the time of publication. Consult your Sherwin-Williams representative or visit
www.paintdocs.com to obtain the most current version of the PDS and/or an SDS